5 Signs of a Well Issue

A residential well is an important and steady resource of fresh, clean water in the house. With proper maintenance, well pumps can last up to 20 years and deliver large amounts of excellent water. However, just like any other system in the house, a well can malfunction or get damaged due to excessive use over time. You’ll likely have to repair or replace it at some point. 

To help you recognize the signs of well issues, we composed the following article. You can rely on it for troubleshooting well problems and resolving them on time, so you never get out of your precious source of water. 

The Well is Pumping Air, Sand, or Sediment

Oftentimes, homeowners notice the air in the water lines from a well pump. This is one of the most common issues in every household. When your kitchen faucet blasts out a mixture of air and water, you’re probably facing two problems. Firstly, your water table might have dropped to the point below the pump, causing it to draw air during the cycle. Secondly, the pump drop pipe might be broken. Drop pipes are prone to corrosion and damage and can develop cracks over time, allowing the air to be sucked in. 

You might also notice sand or sediment in your water, which means the well is filling with sand and silt from the gravel. This happens when the pump drops to a lower level near the bottom of the well, when the well screen degrades, or the pump valves wear out. In this case, we recommend you contact professionals for cleaning up the sand and sediments as soon as possible. 

Low Water Pressure

The causes of low water pressure are many. The most common ones include a well pump malfunction, bad valves, or leaks in the pressure tank. Bacteria can also build up in the well and cause clogs. If you notice a gradual decrease in your water flow rate, you may have a leak somewhere in the system. When water is leaking from the well, contaminants can penetrate the system and make the water unhealthy for consumption. That’s why it’s crucial to repair leaks on time. 

 

Well can leak for many reasons. The most common culprits are corrosion, improper system installation, pressure on the casing, and more. To diagnose and resolve these problems, it’s best to contact a professional leak detection company. While you can look for symptoms of a cracked well casing and signs of well pump failure, you might not be able to diagnose other problems and resolve them properly. 

With vast experience in the industry, professional staff, and proper equipment, Leak Science is here to help you detect and resolve water well leaks with ultimate efficiency. Give us a call and talk with our plumbing expert about your residential well issue!

High Electricity Bills

High electricity bills make one of the signs of a well issue. When the pump wears out or gets blocked with sand, debris, and bacteria, it works extra hard to deliver water. Of course, that results in high electricity bills, so there’s no chance you can miss the issue with the water well.

Closely monitor your monthly costs and go in a full system inspection if you notice increments. In case you run a DIY diagnosis and can’t find the root of the issue, make sure to contact professionals. Even the small problem in the well can evolve and cause larger damage to the system when left untreated. On top of that, you can save a lot of money in the long run by resolving water well problems promptly. 

Questionable Water Quality

Is the well water sputtering out of the tap? Have you noticed the water quality has changed? These are all signs of a well issue you should fix to keep your water clean and fresh. 

It’s unusual for the water to spurt or sputter at the tap or to have small air bubbles. In most cases, these are the symptoms of gases dissolving in the water. Groundwater tables contain gases such as carbon dioxide, methane, hydrogen, and others. Some of these gases can cause safety and health problems if found in the water. Thus, if you notice bubbles in the water or spurts, make sure to take action and inspect your well system. 

Pressure Switch and Pump Continuously Cycles On and Off

It’s not uncommon for the well pump to run continuously in the household. The main culprits are water leaks in the system, corrosion in the water well casing, liner or screen, and more. You can easily detect the issue by inspecting toilet flush valves, reverse osmosis systems, and filter systems. If any of these are leaking or malfunctioning, you probably have an issue with the pressure switch and pump continuously cycling on and off.

What to Do If You Notice Signs of a Well Issue

Troubleshooting well pump problems is not easy. If you notice any of the above-included signs of a well issue, contact your plumbing expert. Don’t try to resolve the problems on your own, because DIY work can sometimes do more harm than good. Professionals can find and resolve all well pump problems without much effort and in a timely manner. They are also very precise and have the tools and equipment necessary to perform the work safely and accurately. 

To keep your well up to code, we recommend scheduling annual well inspection and maintenance. You can easily find professionals that offer well services near you and are certified and trained to perform the job adequately. Rely on them now and then to inspect, maintain, repair, and replace your well pump, and you won’t run out of clean and healthy water ever again. 

If you need help with detecting and repairing leaks, Leak Science is your top choice. Serving Phoenix, Scottsdale, Mesa, Tempe, and Greater Arizona, we provide our clients with top-notch plumbing services. Contact us today and speak about your well issue with one of our leak detection experts!

Posted on: March 4th, 2021 by admin
Still Have Questions?
Call us 480-794-0959
LeakScience Rated 5 / 5 based on 5 reviews.